75252 & 75281 LED FLUSH MOUNT FIXTURE E14660
INSTALLATION AND SAFETY INSTRUCTIONS
Only Qualified Personnel Should Perform Installation of this Product.
Read and Save all Instructions and Warnings for Future Use.
To prevent electrical shock turn off power before
inspection, installation, or removal!
To avoid electrical shock or short circuits be sure
to identify proper wire colors and connect all wires
as per the provided instructions.
Fixture contains an acrylic lens. Handle with care
to avoid personal injury or damage to the lens.
To avoid electrical shock or product failure this
fixture must be used in dry indoor environments
only.
INCLUDED PARTS:
Prior to installation please check that all of the lighting
fixture parts, as shown by letters in the accompanying
drawing, have been supplied in the package. If parts are
missing, please call Customer Service at 1-800-544-4828.
ASSEMBLY AND INSTALLATION:
Helpful Hint: It is sometimes easier to install a wall or
ceiling lighting fixture by temporarily using a stiff length of
non-conductive material - heavy twine or insulated wire - to
suspend the fixture from the electrical box while making
electrical connections. This procedure will serve to hold
the fixture near the electrical box while not allowing it to
dangle from the electrical connections or otherwise allow
the fixture to become unstable or fall during installation.
1. While assuring that the branch electrical circuit breaker
is off, extend the electrical wires from the ceiling outlet
box (1) such that they can be easily accessible for
fixture installation. Fold these wires up to the ceiling
for now.
2. To remove the Acrylic Lens (14) and the Outer Ring
(15) from the fixture , remove the three cap nuts (16)
from the perimeter of the light fixture assembly.
3. Install outlet box mounting screws (12) into the outlet
box holes (4) leaving an approximate ¼ inch gap
between the screw heads (12) and the outlet box (1).
4. Position the fixture pan (9) over the outlet box (1) so
that the outlet box mounting screws (12) protrude from
the keyholes near the center of the fixture pan (9).
5. Slide the fixture pan (9) so that the outlet box mounting
screws (12) slide into the narrow slots of the fixture
pan keyholes.
6. Using a fine pencil, hold the fixture pan (9) flush
against the ceiling and outlet box and mark the ceiling
through the narrow openings of the fixture pan’s outer
keyhole slots (18).
7. Remove the fixture pan (9) from the outlet box by
sliding it free from the outlet box mounting screws (12).
(a) There are stud finders available which can
detect pipes , wires, and obstructions within
hollow walls to prevent drilling accidents.
8. While assuring that there is no plumbing, electrical
wire or other obstruction in the area where the light
fixture will be mounted (a) drill three pilot holes into
the ceiling marks made previously to accommodate
either hollow wall anchors or screws depending
upon the type of mounting surface. Insert the
hollow wall anchors now, if required.
9. Using the wire or twine indicated in the
previous“Helpful Hint”, hang the fixture pan (9) from
the outlet box (1) so that the fixture pan (9) hangs
at a right angle to the ceiling with the LED light
engines (13) facing away from the electrical box
(1).
10. Feed all fixture wires from the fixture pan (9)
through the hole in its center.
11. Loop a section of the lighting fixture ground wire (3)
around the green ground screw and tighten
securely. Connect the end of the ground wire (3) to
the bare ground wire from the outlet box using one
of the provided wire nuts.
12. Using the remaining wire nuts, connect the
conductors of the black wires together. Tighten
wire nut securely and assure that no bare
conductors extend out of the bottom of the wire nut.
13. Now connect the conductors of the white wires
together using the remaining wire nut using the
same precautions as in step #12.
14. Remove and discard the temporary wire or twine
hanger – if used, and carefully tuck all wires into
the electrical box so that they will not be pinched or
obstruct the fixture during the following steps.
15. Carefully install fixture pan (9) by raising it to the
electrical box and allowing the two outlet box
mounting screws (12) to align through all the center
keyhole openings in the fixture pan (9).
16. Slide the fixture pan so that the outlet box screw
heads (12) slip into the narrow regions of the fixture
pan keyholes. Tighten these screws just snugly
now.
17. Install the three anchor screws (11) through the
narrow sections of the outer fixture pan holes and
into the anchors or pilot holes that were previously
drilled in the ceiling. Tighten the screws snugly.
18. Place the Acrylic Lens (14) into the Outer Ring (15)
and intstall this assembly to the mounted fixture
pan (9) with supplied Cap Nuts (16).
Fixture assembly is now complete.
CLEANING:
To clean, wipe fixture with a soft cloth. Clean acrylic with a mild
glass cleaner. DO NOT use abrasive materials, solvents, scouring
pads, or abrasive cleaning powders as doing so may mar the fixture
finish.
(6 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels